2013年12月1日に受信保存した First-MOVE の 1200bps_BPSK信号(wav) を、専用
の Decoder の他に、MixW を使って再生デコードしてみました。次の解析データ
のタイムスタンプは、再生した時の時刻です。
05:28:04 MOVE1/-6*/"b0b>LRT1>I12,?,04 (1200 baud):
_.!.H.4....."ァ..チdA` `・.....d"・ `Sr.@....fa@3.P#`"60......
この解読方法は、以前 JA0CAW局等が行った手法に拠ります。
(1) 事前に Windows_XP のプロパティを次のように設定しておく。
コンパネ - サウンドとオーディオデバイスのプロパティ -
音声 - 音声録音 - 音量 - モノラルミキサーにチェック。
(2) MixW - Mode - Packet - ModeSettings - Modem - VHF1200baud(satellite PSK)
(3) MixW - Mode - Packet - ModeSettings - General -
Emulate KISS TNC on TNC emulation port にチェック。
(4) MixW - Configure - TNC_emulation - Serial_port の設定を確認。
(5) 事前に受信保存した wavファイルを再生する。
(6) 通常はこれでデコードできるが、ここで次の手順を踏む。
(7) PC - Ctrlキーを押しながら、MixW のウォーターフォール内の小さい赤旗を
クリックすると、RX(1)-PACKET という画面が自動的にポップアップする。
(8) PC - Ctrlキーを押しながら、MixW のウォーターフォール内の小さい赤旗を
左右に数mm、再生音の赤い筋を両脇の小さい赤旗の帯で挟むようにドラッグ。
(9) このように調整して再生すると、そのポップアップ画面内に受信データが
上図のようにデコードされる。
First-MOVE decoded using MixW
05:28:04 MOVE1/-6*/"b0b>LRT1>I12,?,04 (1200 baud):
_.!.H.4....."_.._dA_ _*.....d"* _Sr.@....fa@3.P#_"60......
How to decode "First-MOVE using MixW" is due to the method of JA0CAW has before.
(1) Set the properties of Windows_XP in advance as follows.
Start - Settings - Control Panel - Sound and Audio Devices
- Voice - Recording sound - Volume - Check Wave or Monaural Mixer
(2) MixW - Mode - Packet - ModeSettings - Modem - VHF1200baud(satellite PSK)
(3) MixW - Mode - Packet - ModeSettings - General
- Check "Emulate KISS TNC on TNC emulation port"
(4) Verify the setting in MixW - Configure - TNC_emulation - Serial_port.
(5) Make the playback of the wav file that you received previously saved.
(6) Perform further the following steps, although you can be decoded here usually.
(7) Click on the small red flag in the waterfall of MixW while pressing Ctrl_key,
then the window "RX (1)-PACKET" will be poped up automatically.
(8) Drag a few millimeter the left or right the small red flag in the waterfall
of MixW while pressing Ctrl_key, so as to sandwich in the band of the red flag
the stripe representing the playback sound.
(9) Make the playback of the wav file while adjusting like this, then the data are
decoded in the pop-up window. Timestamp is the time when you playback it.