Re: UISS v5.3.2 registered2013年02月10日 07時27分

Subject: Re: UISS v5.3.2 registered
From: Guy
To: Mineo Wakita
Date: Sat, 9 Feb 2013 17:58:39 +0100

Hi Mineo,

Your have the Pro-edition! No mistake!
The Unregister button is to remove the registration key.
It does NOT mean that you have an unregistered copy.

Hope this helps,

-----Oorspronkelijk bericht-----
Subject: UISS v5.3.2 registered
From: Mineo Wakita
To: on6mu
Sent: Friday, February 08, 2013 12:17 PM

Thanks for your UISS update to v5.3.2

I registered as Pro-Edition.
My UISS pro_key is "******".

Then it's displayed definitely with
"Pro-Edition Registered To Mineo JE9PEL*" in the screen upper part.

But, it remain a red button of the indication
"Unregister" in "UISS - Help - About UISS".

Why is it?

JE9PEL, Mineo Wakita

Setup Shadow Experiment in "UISS - Help - UISS Manual"

Simply follow the instructions of the Wizard in the Help-menu.
The 'Wizard' will allow you to setup UISS for transmitting ISS Shadow
Experiment beacon data.

Remember that transmitting during the Shadow Experiment is only allowed
by stations who are granted the right to do so (Master Stations).
However, everybody is encouraged to send their reception reports to:
Information Storing Center (shadow@*****.ru) or (vastra@*****.ru)!
No need to use this wizard for reception only of ISS Shadow packet

Summary: the beacon, during the Shadow Experiment, will transmit 1
minute of continues packets with an interval between each packet set in
the Wizard (or beacon) of xx seconds.
An additional pause of xx (Interval beacon pause) seconds added after
every minute of beacon transmissions.

Or do it without the wizard:
To setup UISS for the Shadow Experiment, go to menu Setup->Beacon Settings:
- Activate the beacon
- Enter a beacon-interval of 3 seconds. (This will let UISS know that the
  user could want to use its Shadow Experiment features.)
- Click on the bottom-left button with the blue V-icon representing OK
  (to apply the beacon settings).
- Confirm the dialog which asks the user if he/she wants to enable the
  Shadow Experiment mode.
- You'll see a new option "ISS Shadow Experiment". Here you just need to
  enter your country's ISO code (example BE = Belgium)
  (ISO-List can be found in your UISS Folder)
- Now click again on the blue V-icon button

UISS will start to transmit the beacon according to Shadow Experiment
prefered packets (including digipeater etc.):

Fm ON6MU To BEACON Via ARISS <UI pid=F0 Len=38 >[23:42:24]
SpEx SHADOW 23:42:24 *BE* 30-11-2007/
Fm ON6MU To BEACON Via ARISS <UI pid=F0 Len=38 >[23:42:27]
SpEx SHADOW 23:42:27 *BE* 30-11-2007/

Want it even easier? Just use the build-in wizard and follow the steps.
This feature can be found in Setup-menu.
Space digipeaters like ISS, PCsat and others are NOT intended for

[More information] (EN) (EN)   (JP)   (JP)

ISS OFF / NO-44 ON2013年02月10日 16時51分

やはり、スクールコンタクトの後、ISS OFF のままとなっています。
夕方のパスでは、同時刻に遠くの方で、NO-44 が聞こえていました。

ISS  , 16:33-16:42JST, 10 Feb 2013, Ele 14 S-E-EN, 145.825MHz FM
NO-44, 16:24-16:39JST, 10 Feb 2013, Ele 66 NW-W-S, 145.827MHz FM

AENEAS beacon2013年02月10日 21時45分

自局でデコードできるのは、いつも 1~2個。

21:13-21:27JST, 10 Feb 2013, Ele 64 NW-W-SE, 437.600MHz FM
KE6YFA-1>CQ,TELEM [02/10/13  21:22:58] <UI>:

AENEAS Beacon Data Decoder, Rev 1.1
Opening file at 30210aen.dat
AENEAS Beacon TLM Packet found:
Total length: 29
Unused: 0x02 0x00 
Time: 1/1/11-6-16:2:0
Reboots: 1287
Last Reboot Cause: 0
Flash Status: 0
Bit 0 = 0 : Device is ready.
Bit 1 = 0 : Device is NOT write-enabled.
Bit3&4= 1 : All sectors software-protected.
Bit 4 = 0 : WP is asserted.
Bit 5 = 0 : Last op successful.
Bit 7 = 0 : Sector Protection Registers unlocked.
Payload Write Pointer: 1273856
Telemetry Pointer: 7729152
Radio Status: 65
No detailed Radio info yet
Misc Write Pointer: 1104765632
Done: End of stream reached.